Tips On How To Extend Smok Pen Recharge Time


Tips On How To Extend Smok Pen Recharge Time

The Smok Pen is really a new pen that was created by two guys in California. They wanted to develop a cool writing instrument that looked like a real pen but had the ability to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has taken the marketplace by storm.

smok pen

The Smok Pen includes a built quality that is just great. I found that even though it can be an electronic pen the build quality is simply as good as the pens that I’ve reviewed. For the reason that of how they made the most notable cap. You don’t need to worry about the cap cracking or breaking on you Smok Valve Pen.

Both biggest differences that separate the Smok Valve from other pens is the form of the coils and the way that they are built. Generally the coil on a Smok Pen is bigger than on other pens. I believe that they did this on purpose, to help make the pen feel more substantial.

If you take a glance at a Smok Pen, you will notice that your body of the pen is round rather than smooth like other pens. On the back of the pen there is a little tab that houses the coil. When you press on the tab you can easily turn the heating element on and off. I must say i liked this feature since it allows me to utilize the Smok Pen 22 whenever Personally i think like smoking.

To utilize the Smok Pen you must keep the heat button pressed. Once the button is pressed, the heating element will Vape start to warm up. Once it gets to the appropriate temperature you can switch off the heating element. Smok recommends using a 22mm tank. I prefer a more substantial tank, but that’s just me.

Once you put your Smok Pen in to the tank you will see a indicator light seriously. The indicator light will stay green unless you put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is very important always put your pen into the charger before you apply the e-liquids to the coil heads. Additionally it is important to do that before putting your e-liquids into the coil heads.

After you have completed this step, you should always check to see if you are at the right temperature for the coils to fire. If not then you should turn the power off and try again. In case you are still not satisfied with your Smok Pen then I suggest you take it set for some troubleshooting. This is exactly what I’d call the “troubleshooting process” because sometimes things just usually do not work as they should. I would recommend that you perform the next two steps, then go on and check the Smok Pen to see if it still has the electronic charging port.

Before you go any further you should remove the battery from your pen and unscrew the magnetic cap. You should then remove the plastic sleeve that holds the sub-ohm. There is a wire that runs through the Smok’s body that is green in color. You need to loosen this wire using pliers. After you have loosened this wire you can then access the sub-ohm. You need to then remove the wire from the Smok’s body and carefully insert it in to the Smok pen’s electrical port, being careful never to touch any of the coils.

When you have placed the sub-ohm tank in to the pen you need to then place the rest of the components like the wattage, the batteries and the heating element into the included microwaveable microwave oven. Start the power and follow the on screen instructions. You need to place the pen’s battery into the microwave and activate the setting. You should then wait approximately 30 seconds before turning it back off. When you initially put the pen into the microwave the electronic reading will show a low voltage protection setting. If this setting will not automatically get set then you should follow the on screen instructions.

After the Smok Pen has already reached the temperature that it requires to reach you need to then connect the two wires to the positive and negative on the positive post on the Smok unit. You should then connect the other end of the battery to the negative post on the negative side of the Smok unit. The ultimate step is to connect the positive cable to underneath of the Smok’s power switch.

After all of the components have been placed into the pen, you should turn the power on. After the first test run, you have to be able to see the battery life indicator light come on. If you do not see any sign of life from the Smok Pen, you need to remove the battery from the pen and replace it with a brand new one. For your convenience there is also a green light which might be pressed in order to confirm the battery charging status. If you have done these things and you also do not see the green light indicating charging, you should replace the battery.